Efcolor can be used on a wide range of surfaces including wood, porcelain, glass, silver, copper, bronze, brass, stone, ceramic or any other surface that can be fired at 150ºC.
Step 1) Sift your powder onto your chosen backing.
Step 2) Move onto your firing plate.
Step 3) Insert into an oven that is pre-heated to 150ºC.
Step 4) Remove after 3-5 minutes (be careful, it will be hot).
If you are doing the back, then just repeat the above, but don't lay it colour down onto your firing plate, as the colour will melt again
Efcolor can be used on a wide range of surfaces including wood, porcelain, glass, silver, copper, bronze, brass, stone, ceramic or any other surface that can be fired at 150ºC
Efcolor overglaze powders are ideal for giving an enameled appearance to your creations, while avoiding the constraints of traditional enamel firing with a specialized oven!
Use this Efcolor Adhesive to enamel curved shapes and vertical side pieces with Efcolor powder!
Efcolor Low Temp Enamel Primer is a primer (adhesive) for Efcolor powder when applying to absorbent or awkward shapes, for instance a curved, carved or undercut surface. It will help the powder adhere better. Can be diluted if required – dilute and clean up with water.
Structured Powder Opaque Efcolor for cold enamelling at 150 ° C, 25ml
Copper foil, 300 x 200 x 0.3 mm, for enamelling, decoration, creation
Lot of 10 small round copper pendants, 1 hole, ø 1.5 cm, thick. 0.8mm, for enameling
Set of 10 Copper Pendants, Butterfly 22 x 22 mm, 0.8 mm thick, for enamelling
Lot of 10 Copper Pendants, Octagonal, 2 holes, roughing 30 x 12 x 0.8mm, for enamelling
Lot of 10 Pendants, copper, Dwarf, 1 hole, 34 x 21 mm, blank for enameling
Efcolor oven with accessories, for cold enamelling, works with candles
Set of 10 Copper Pendants, Windmill 3 x 2,2 cm, 0.8 mm thick, for enamelling
These Sieve Tops help provide easy application of Efcolor enamels. They measure 20mm in diameter and are specifically designed for use with 10ml tubes of Efcolor enamel. Simply put the Sieve Top onto the tube of resin based enamel powder and use, for even distribution of powder over your item of jewellery or copper blank. Supplied in a pack of 20.
Set of 5 Efcolor powder colors, 10 ml, blue color chart, 2 sieves, for cold enamelling, baking at 150 ° C
Efcolor oven with accessories, for cold enamelling, works with candles
Enamel powder, cold, opaque Efcolor, 25 ml, for cooking 150 ° C
Set of 5 Empty tubes with stopper, ø 20 mm high 50 mm, for 10 ml
Set of 5 Efcolor powder colors, 10 ml, pink color chart, 2 sieves, for cold enamelling, baking at 150 ° C
Set 5 colors, Efcolor Enamel powder, 25 ml, primary color, total 125 ml, 2 sieves tops, for enameling, baking at 150 ° C
Set 5 colors, Efcolor powder, 10 ml, yellow color, 2 sieves, for cold enameling, baking at 150 ° C
Set 5 colors, Efcolor powder, 10 ml, soft color, 2 sieves, for cold enameling, baking at 150 ° C
Efcolor overglaze powders are ideal for giving an enameled appearance to your creations, while avoiding the constraints of traditional enamel firing with a specialized oven!
Efcolor Enamel is a low temperature resin based enamel powder which can be used on metals such as silver or copper, along with glass, wood, porcelain and stone. As with all Efcolor enamels, this enamel does not require the use of a kiln, as it can be fired in a conventional oven at 150°C. This fabulous product enables anyone to create enamelled jewellery designs with ease. Simply sieve onto your chosen backing, transfer to a firing plate, and fire in a pre-heated oven at 150°C for 3 - 5 minutes. Care must be taken when removing your piece from the oven as it will be hot. A Sieve Top may be useful for easy application of the powder. This resin based enamel is supplied in a 10ml pot.
These Sieve Tops help provide easy application of Efcolor enamels. They measure 20mm in diameter and are specifically designed for use with 10ml tubes of Efcolor enamel. Simply put the Sieve Top onto the tube of resin based enamel powder and use, for even distribution of powder over your item of jewellery or copper blank. Supplied in a pack of 3.
Efcolor overglaze powders are ideal for giving an enameled appearance to your creations, while avoiding the constraints of traditional enamel firing with a specialized oven !
Transparent finish: veil of color that reveals the background or the pattern of the support.
Set 5 colors, Efcolor powder, 10 ml, reds color, 2 sieves, for cold enameling, baking at 150 ° C
Set of 5 Efcolor powder colors, 10 ml, green color chart, 2 sieves, for cold enamelling, baking at 150 ° C
Set 5 colors, Efcolor Enamel powder, 25 ml, Summer color, total 125 ml, 2 sieves tops, for enameling, baking at 150 ° C
Efcolor can be used on a wide range of surfaces including wood, porcelain, glass, silver, copper, bronze, brass, stone, ceramic or any other surface that can be fired at 150ºC.